Lock-In Wood Sanding Sealer
Interior/Exterior

DESCRIPTION
Safecoat Lock-In Wood Sanding Sealer is a unique, fast drying, sandable sealer especially formulated to reduce raising of the grain on raw wood when waterbased finish products are applied. Safecoat Lock-In also helps to prevent bleed through of naturally occurring oils, tannins, turps and resins in wood. This is especially important for appearance and for those with sensitivities to such bleed thru materials.

BENEFITS
Superior, sandable sealer. Low odor, non-offensive to installer and occupant. As a first coat on raw wood to which a finish coat such as paint, stain or clear finish is to be applied, helps prevent bleed through of naturally occurring oils, turps, tannins and resins that can discolor finish coats over untreated raw wood. Safely used by and for the chemically sensitive. Fights indoor air pollution by sealing in naturally occurring outgassing. Very low VOC content, meets or exceeds all federal and state air quality regulations, including California. Contains no formaldehyde.

USE ON
New wood. Two coats of Safecoat Lock-In should be used on porous wood, especially tannin-ladin cedar and redwood.

More Info (PDF)
Lock-In Sanding Sealer
MSDS

MexeSeal
Interior/Exterior

DESCRIPTION
Safecoat MexeSeal is a low odor,
waterbased, medium gloss clear sealer. It is suitable for use on porous interior tile or masonry surfaces where oil and water repellency are desired. It is ideal for long term protection against food, oil and water stains on residential
or commercial floors. Safecoat MexeSeal is non-hazardous and non-flammable - a total replacement for high solvent content systems.

USE ON
Safecoat MexeSeal is recommended on substrates such as the following; unpolished marble, limestone, granite, sandstone, slate, fireclay (brick, tile,
terra cotta, pavers), concrete (brick, tile, precast panels, cast in place). Always test in small, inconspicuous places before full application. Safecoat MexeSeal is generally not suited for polished surfaces; test first. MexeSeal is also effective as a sealer and protectant for porous wood surfaces such as redwood, cedar and pine.

BENEFITS
Hard, durable medium gloss finish. MexeSeal is suitable for recoating many waterbased sealers (always test first). Slip resistant in dry conditions. Good resistance to scuffing, black heel marks, oil and water. Easy clean up with dry or damp mop - dirt and foreign matter do not penetrate the treated surface.
Safely used by and for the chemically sensitive. Fights indoor air pollution, seals in the outgassing from the substrate. Very low VOC content, meets or exceeds all federal and state air quality regulations, including California. Contains no formaldehyde.

More Info (PDF)
MexeSeal
MSDS

Penetrating WaterStop
Interior/Exterior

DESCRIPTION
Safecoat Penetrating WaterStop improves water resistance and repellancy in a wide variety of surfaces, including brick walls, concrete foundations, stucco, stone and most unglazed tile. Because Safecoat Penetrating WaterStop is not toxic and low odor, it is ideal for use indoors instead of a typical high solvent content sealer; yet, it is durable enough for use outdoors. It is partiuclarly useful as a perioduc maintenance coat for surfaces originally treated with Safecoat WaterShield.

USE ON
Safecoat Penetrating WaterStop is recommended for porous brick, mexican pavers, concrete block, concrete and stucco. It can also be used over wood to increase water repellency and reduce water absorption.

BENEFITS
Good water resistance for up to five years when properly applied. Low odor, non-offensive to installer and occupant. Safely used by and for the chemically sensitive. Fights indoor air pollution, seals in the outgassing from the substrate. Zero VOC content, meets or exceeds all federal and state air quality regulations, including California. Contains no formaldehyde.

More Info (PDF)
Penetrating Water Stop
MSDS

Safe Seal
Interior

DESCRIPTION
Safecoat Safe Seal is a multi-use, waterbased, low gloss sealer for highly porous surfaces such as particle board, plywood, processed wood and porous concrete. Used primarily to reduce toxic outgassing: in particular, it is highly effective at sealing in formaldehyde outgassing from processed wood such as plywood, particle board and pressed wood. Safecoat Safe Seal is virtually odorless on application and odorless once cured.

USE ON
Porous surfaces such as processed wood products, concrete, wood, new drywall, grout and plaster. If used as a grout sealer, wipe excess off tile with a damp cloth or sponge while still wet. Test surfaces first in inconspicuous areas to be sure product absorbs into surfaces completely. Excellent at controlling formaldehyde emissions of open faced and faced fiberglass batt insulation
- simply fog spray surfaces.

BENEFITS
Highly effective at sealing in toxicity of underlying surface. Safely used by and for the chemically sensitive. Low odor, non-offensive to installer and occupant. Fights indoor air pollution, seals in the outgassing from the substrate. Low VOC content, meets or exceeds all federal and state air quality regulations, including California. Contains no formaldehyde.

More Info (PDF)
Safe Seal
MSDS

Hard Seal
Interior

DESCRIPTION
Safecoat Hard Seal is a multi-use, clear gloss sealer especially formulated to provide mar resistance to both low and high porosity surfaces. Because it forms a continuous membrane when applied properly it is particularly effective at sealing in any pollution or toxic chemical compounds outgassing from the surface to which it is applied.

USE ON
Typically used on previously uncoated and unsealed woodwork, cabinetry, vinyl or porous tile. To prevent outgassing of previously coated surfaces, can also be applied over existing paints, stain and colorfast wallpaper. When applying to a previously coated surface test in inconspicuous places for satisfactory appearance. Correct application will slightly deepen color of existing surface.

BENEFITS
Hard, durable clear gloss appearance. Powerful sealer to prevent outgassing of pollution and toxicity from underlying substrate. Low odor, non-offensive to installer and occupant. Safely used by and for the chemically sensitive. Fights indoor air pollution, seals in the outgassing from the substrate. Very low VOC content, meets or exceeds all federal and state air quality regulations, including California. Contains no formaldehyde.

More Info (PDF)
Hard Seal
MSDS

WaterShield
Interior/Exterior

DESCRIPTION
Safecoat WaterShield is a clear, versatile, controlled penetration water repelling sealer which provides an invisible barrier against water and resists oils, grease and similar liquids. It is fast drying, has excellent adhesion, and is easy to apply. In addition to sealing and providing a protective barrier against water migration, it helps to harden, dust proof and control efflorescence in masonry surfaces.

USE ON
Porous cementitious materials such as concrete, stucco, brick, block, terrazzo and unglazed tile. Also excellent as a wood sealer.

BENEFITS
It is not toxic, non-flammable, lead and formaldehyde free and does not contain surface contaminating silicones, making it a desirable coating for interior or exterior use. May be used on painted surfaces and may be painted over when dry. Dries clear and does not discolor.

More Info (PDF)
Water Shield
MSDS

Grout Sealer
Interior

DESCRIPTION
Safecoat Grout Sealer is a clear, moisture resistant sealer for porous tile grout and other cementitious surfaces. It actually reacts with and becomes a part of the grout, increasing water resistance and minimizing the penetration of liquids, helping to prevent staining and giving a wearable, washable surface. Like all Safecoat products, it is as safe and not toxic as possible, formaldehyde free and virtually odorless, giving off no offensive chemical fumes. Dries clear without discoloration.

USE ON
Unsealed tile grout. May also be effective on a variety of other porous cementitious surfaces (test first). For previously sealed grout, conduct several small test patches for absorption and compatibility.

BENEFITS
Good water resistance for up to five years when properly applied. Low odor, non-offensive to installer and occupant. Safely used by and for the chemically sensitive.  Fights indoor air pollution, seals in the outgassing from the substrate.  Zero VOC content, meets or exceeds all federal and state air quality regulations, including California.  Contains no formaldehyde.

More Info (PDF)
Grout Sealer
MSDS